back button black v05

Hall-effect angle sensor ICs for motor position applications

Hall-effect angle sensor ICs for motor position applications

09 July 2015

Dual-die devices designed for safety-critical automotive applications

Allegro MicroSystems: The new A1331 and A1334 from Allegro MicroSystems Europe are a family of contactless, Hall-effect based magnetic sensor ICs for high-speed motor position sensing in safety-critical automotive applications

Allegro’s dual-die A1331 and A1334 angle sensor ICs are based on vertical Hall-effect technology with system-on-chip architecture that provides fast output refresh rates and low signal path latency.

Each device is offered in a TSSOP-24 package that contains two individually sawn, electrically isolated silicon ICs. The dual-die feature makes them suitable for use in safety-critical applications that require the use of redundant sensor ICs, especially in ASIL compliant automotive systems. The A1334 is also offered in a single die configuration in the TSSOP-14 package for applications that do not require redundancy.

Typical applications include electronic power steering or power braking motor position sensing, transmission actuator position sensing, throttle/pedal position detection, and other systems that require accurate measurement of angular or rotary position.

The A1331 and A1334, with their onboard digital signal processing functions and EEPROM for factory and customer programmability, are designed specifically for on-axis/end-of-shaft angle sensing applications that require ultra-fast output refresh rates and low signal path latency.

These sensor ICs include a 4-wire 10 MHz SPI interface with a 25 µs output refresh rate and a nominal signal path latency of only 60 µs. In addition, the ICs can operate directly off a vehicle battery, supporting a wide 4.5-14.5 V supply voltage range while consuming just 10 mA (maximum) of supply current per silicon die. They also include signal path and I/O diagnostics designed to meet the stringent needs of ASIL safety requirements.

Both devices can operate in a low RPM mode, to support up to 12 bits of output resolution, and in a high RPM mode, to support situations demanding faster refresh rates and lower single path latency. As part of their signal processing functions, the ICs include automotive-grade temperature compensation to provide accurate angle measurements over the full operating temperature (-40°C to +150°C) and voltage (4.5-14.5 V) ranges of the devices.

The A1331 and A1334 output signals maintain a high level of accuracy over a wide magnetic field range, and can operate over a field range from less than 300 G to greater than 1000 G. On-chip EEPROM technology also enables flexible customer programming of the ICs.

The A1331 IC is unique in that it contains both a micropower mode of operation and an internal electronic turns counter function. Both of these features are important in electronic power steering applications, where it is important to keep track of the absolute position of the steering wheel over multiple revolutions. The A1331 can be connected to the vehicle battery, and placed into micropower mode (100 µA average consumption per die) when the automobile is in the key-off state.

The A1331 will detect turning of the steering wheel while in micro-power mode and will sense and store the revolution count of the steering wheel, even while the car is in the key-off position. As a result, when the vehicle is powered up (key-on position), the steering system is aware of the absolute position of the steering wheel. This turns counter function counts in increments of 180 mechanical degrees, with a range of 511 positive increments and 512 negative increments.

About Allegro
Allegro MicroSystems, LLC is a leader in developing, manufacturing and marketing high-performance semiconductors. Allegro's innovative solutions serve high-growth applications within the automotive market, with additional focus on office automation, industrial, and consumer/communications solutions. Allegro is headquartered in Worcester, Massachusetts (USA) with design, applications, and sales support centers located worldwide. Further information about Allegro can be found at www.allegromicro.com

Allegro MicroSystems Europe, headquartered in Chertsey, United Kingdom, is the European sales and marketing operation, and operates a network of representatives and distributors throughout Europe.  Allegro also has an engineering design centre in Edinburgh in Scotland and an application and marketing centre in Annecy in France.

  • Allegro MicroSystems, LLC
    115 Northeast Cutoff
    Worcester, MA 01606
    United States / America
    Tel.: +1-508-854-5359
    Web : www.allegromicro.com
  • company website button
  • all entries button

back button black v05